Sunday, 16 October 2016

Criterion A- Inquiry and Analysis







reflection:
this is the solar powered ac which i made on Umake as i said on the other reflection i like this software better because it allows you to free draw your own ideas and designs on a touch screen with a special pen. i started by drawing the base and the lines like a normal drawing then i started to do the front to make it 3D. once i did all the sides, even the top i started to connect all the lines together so it creates the design as a whole, then you create the surfaces which basically finishes the creation. then you can customize it by adding textures and colors.













reflection :

this is the full set of the solar powered ac which i made on tinkercad but i had designed it also on another software because i did not like how i made it on tinkercad since there was allot of things i couldn't do on this software like free draw and sketch my design because on tinkercad you can only put shapes which is very restricted as a software. unlike "Umake" the other software i used, you can actually draw your own design and add textures and surfaces. although the design might look nicer on tinkercad the actual design looks more real on Umake. it is much more accurate to adjust curves and lines on Umake because you can edit them, you can also attach surfaces to other lines and shapes. you can customize the color of your creations and edit them. in conclusion i think Umake is a better software because it is easier to customize and create your own free sketch also because its on an ipad and you can use the touch screen and i also use a special pen which allows you to draw like if you are on paper.      
















reflection:
this was my first sketch about my creation, this is basically a solar panel generated ac that can be placed in the car when the weather is hot. the solar panels can be placed on the top of the car were they will not be noticed. the electricity generated from the panels will be sent to a battery which will be sent to the ac. the design of the ac is very simple and small so that it could be placed in a corner of the car. the ac will come in many different colors and maybe in the future they could look better. the ac works by a fan at the top and the air produced will go through a cooler which is in the middle of the ac and finally the cool air will come out from the end whole. the direction of where the air goes is up to you since it can be adjusted my final design will be made on two softwares because i like one of these softwares better but i still have to make it one the other one. the softwares are called TINKERCAD AND UMAKE  



















design brief 



















DESIGN SITUATION -1 

prOBLEM SOLVING THROUGH CREATION - CHILD FRIENDLY SYRINGE.. 
The UAE Nurses Association claims that one of the most difficult parts of their job is dealing with small children who have a fear of needles.  Although the association has some tips and tricks like putting numbing cream to partially freeze the surface of the skin before injecting medicine, sometimes the anxiety levels of small children are so high that it is difficult to get them to hold still.  If only there was an easier way to administer medicine within the syringe.

My design situation 1 

many kids around the world are very scared of needles and this makes it very hard for the doctors at hospitals to take an injection on a child that is constantly moving and agitating. Most of the time the doctors try to distract the child but in the end that child will realize that he is going to be injected. even my younger sister is very scared of needles and we always have to listen to her screams and wining, this is also very dangerous for the child to be moving when the needle is being injected because it could brake inside the child's arm. So what i have made could hopefully change that because i made a syring using the software tinker cad but this syring is different, it looks like a plane so the children wont suspect much also because the syringe is covered with a tube but unfortunately in the picture below it couldn't be seen   
my design situation 2
many people are usualy late to school or to other things and thats because they dont have a clock with them or at home, but even people that do have a clock still dont pay much atention to it so i made a clock that wil make children of all ages look at it. the clock i created using tinker cad software is a normal clock but on the top of the clock it says  time to go, in short of TTG so when the alarm would go on that text will lite up and make sounds and will even vibrate in a funny way and this would attract the attention of the kids and let them remember not to be late. 

1 comment:

  1. While you have provided designs of the 3D creations you need to annotate your designs.
    But you have come a long way in providing a design situation, design and the creation of the product.
    Well done. You have achieved the following levels in each criterion.
    Criteria A-3,B-3,C-5,D-3
    Now focus on step by step instructions provided in class and my blog to achieve greater levels in the future.
    Regards
    Ms.Veena

    ReplyDelete